Trunnion Mounts
Uncategorized

Benefits of Trunnion Mounts for Industrial Lights and Equipment

Looking for new ways to improve illumination and light distribution at busy work sites? Try trunnion mounts.

Mounts for industrial lighting systems vary, depending on their features and mechanisms. A great comparison is surface mounting and trunnion mounting. The first mounting option offers increased stability, but with limited adjustable settings. A trunnion mount addresses such limitations by providing a flexible bracket for adjusting the base of the unit.

Trunnion Mount 101

By definition, a trunnion is a pivoting component that can be used for mounting and adjusting. Such mechanisms were first used on military cannons. These days, the term is also applicable to a shaft or component that is used to support a tilting or adjustable plate. This latter definition is widely applied in industrial lighting systems.

Trunnion mounts are secured close to the light’s center of mass. As a result, stability is increased and operators can adjust the light up and down. Outside of rugged work sites, trunnion mounts on lights can be found on commercial stages. For such applications, a strip light may incorporate a trunnion mount at both ends for mounting on the floor. Mobility can be enhanced by installing casters at the bottom of the mounts.

Trunnion Mounts and Maintenance 

Businesses that use elevated lighting systems on a regular basis may directly benefit from trunnion mounts. This type of mount leaves the back of the light’s housing exposed, which offers seamless access to the internal components of the unit. Because of this, operators can easily perform inspections and repairs on the luminary.

Trunnion mounts are also useful for operations that require gloved hands. Some trunnion-style mounting brackets leave an open gap between the brackets and the lamp, allowing individuals to position or setup the unit without removing one’s gloves. Lastly, this type of mount can be supplemented with magnets at the base for bolt-less mounting configurations on compatible surfaces.

Share Button

Continue Reading

LED Panel Light
Led Lights

What is an LED Panel Light for Industrial Facilities?

Businesses have numerous options, when it comes to upgrading outdated or traditional lighting systems. These days, most companies are looking to improve illumination in the work site by adopting LED luminaries. Replacing fluorescent lamps with LEDs can be achieved using the LED panel light. The units are specifically designed for indoor settings, such as manufacturing floors, control rooms, commercial offices and schools.

LED Panel Light 101

LED panel lights feature a handful of unique properties for robust illumination. Comprised of three layers in its housing, the unit contains the LED chips, a light guide plate and a diffuser. A heat sink component may come with the light, which helps mitigate thermal fluctuations. It is important to note that LED panel lights may incorporate SMD LED chips to boost illuminative performance.

Most LED panel lights are constructed of lightweight aluminum. This helps operators install the fixtures in recessed configurations. The setup offers space-saving benefits for tight work spaces.

From a cost perspective, LED panel lights are less expensive to operate and maintain. The products are capable of meeting the standard 50,000+ hour expected lifespan of LEDs. Furthermore, the solid state lamps can withstand rough impacts better than filament-based luminaries, including incandescent units.

Applications and Considerations

Fluorescent lights are known for their accurate CRI ratings, which is highly preferred by businesses that specialize in product manufacturing, commercial paint spraying services, industrial labs and learning institutions.

Keeping this in mind, LED panel lights should be applied to similar applications.

The two main configurations during installation for the 12v LED lights are recessed mount and suspended ceiling mount. As mentioned earlier, recessed mounting is perfect for promoting a spacious workplace. Suspended ceiling mounts are suitable for overhead illumination over a general workspace or area. For low ceilings, operators can choose to install the unit directly on the ceiling (no suspension).

Share Button

Continue Reading

Led Lights

7 Things You Didn’t Know About Led Spotlight

Most cities have decided that, in the coming 3 years, to replace around 6,500 conventional lights with Ledspotlight. The reason for this is the main benefit of Led products which is the energy efficiency. Led spotlight can be 6 to 10 times more energy efficient than traditional ones. This might be old information for you, but what are the other things you didn’t know about Led spotlight?

Definition of the led spotlight:

It stands for Light-Emitting-Diode, which is an electrical component that lets electricity pass in only one direction.

The 1st Led spotlight was invented by Nick Holonyak Jr in 1962:

The first visible Led spotlight appeared in 1962 on the hands of Nick Holonyak Jr. while working for General Electric (GE). Found as a great invention for saving energy, more have been manufactured. The early Led were produced only in red lights. With the rise of their popularity, manufacturers started the production of coloured ones like green, blue and even white.

Led lights can be used for 20,000 to 50,000 hours:

Good quality bulbs can run, non-stop, for 20,000 hours, which is a bit more than 2 years, while high quality Led spotlight products have a non-stop useful life that can reach 50,000 hours, which amount to a bit less than 6 years. They are definitely more economical than traditional lights which can illuminate for around 1,200 hours.

Led spotlight waste less heat than conventional lights:

The efficiency of the spotlight is due to their low conversion of energy into heat; 80% of the generated power is transformed into light, and 20% into heat. In contrast, conventional bulbs convert around 80 to 90% of the energy into heat, and the remaining into the light. This transformation of energy makes Led spotlights and globes cooler than traditional ones. Read more.

Light-emitting-diodes don’t attract bugs:

One of the practical reasons to use this energy saving light bulbs is that they don’t attract insects as hot lights do.

Led spotlightis adopted for a different use:

With the energy saving light becoming more common, their use is now being multiplied for several purposes. The most popular use of these lights, other than the bulbs, is on computer monitors and TV screens. But did you know that they are also used publicly in traffic lights, vehicle brake lights, billboards and others?

Led spotlight are environmental friendly:

The benefit of led spotlight globes and spotlights affects your electricity bill. It can help you economise around 30% of the money spent on electricity. On another hand, LEDs are known for being environmentally friendly. The use of non-toxic substances makes them harmless to nature. No damaging gazes are being discharged into the open air.

CONCLUSION

Briefly, led spotlight products can be today’s best choice of lighting on many levels. However, you have to be careful when purchasing from Led spotlightstores or manufacturers. It’s been noticed that many of them are giving wrong information about their products leading the buyers to purchase deceitful products. For more information visit: http://www.larsonelectronics.com

 

 

Share Button

Continue Reading

food processing lights
hazardous area lights

NSF Zone Classifications for Industrial Food Processing Lights

The National Sanitation Foundation (NSF) governs the application of food processing lights for manufacturing facilities, as well as commercial kitchens. For lighting systems, the non-profit public health agency classifies certain food-related locations into the following categories: Non-food Zone, Splash Zone and Food Zone.

This article provides information about each NSF classification, under the NSF C-2 listing procedure.

Non-food Zone

Starting with non-food zone areas, this level of certification is for dry-processing locations, storage rooms and commercial kitchens. The lamps do not normally feature extreme resistance to high-pressure jets or corrosive cleaning agents. Therefore, the fixtures should not be used in sections of the facility that exposes the units to persistent washdowns. The possibility of contamination is also high with non-food zone lamps.

Splash Zone

This type of location in the facility does not regularly come in direct contact with food. Instead, the NSF-rated lamps are constantly exposed to splashes from washdown sessions. Because of this, food processing lights should be designed to withstand wet or damp locations (depending on the application). Glass lens is not typically used for splash-zone fixtures, due to the possibility of breakage, when exposed to high-pressure jets. The fixtures should also offer some form of corrosion resistance to deter cleaning solvents or agents.

Food Zone

Food zones, as the name of the classification suggests, are locations that handle consumable products, usually at their final stages of processing. It is important to highlight that materials for food zone fixtures can also be used in non-food zone and splash zone lights. Interestingly, other types of equipment can be found in this category, including chopping boards, industrial tables and conveyor systems that push food products to various sections of the establishment.

In addition to observing NSF classifications, food processing facilities must also adhere to FDA and USDA guidelines. To purchase hazardous area lighting fixture please visit http://www.larsonelectronics.com/c-154-explosion-proof-lights.aspx

Share Button

Continue Reading

induction lights
Led Lights

LEDs vs Induction Lighting for Industrial Work Sites

LEDs are currently top choice for lighting system upgrades in rugged facilities. As a lighting technology that is setting the standard for the sector, when it comes to performance and illuminative output, it is expected its position will be challenged by engineers and lighting manufacturers.

In the past few years, upgrades to induction lighting have made it more viable for applications that require persistent illumination. Like LEDs, the lamps come with an impressive lifespan of 50,000 – 100,000 hours. Moreover, it can retain lumen output at 70 percent after 60,000 hours.

No Electrodes, No Problem

Induction lighting fixtures utilize gas (like a fluorescent unit) inside the bulb for illumination. The main difference between the two lighting technologies is the use of electrodes. Traditionally, fluorescent luminaries rely on electrodes to kick start current inside the lamp. Continuous striking of the arc contributes to wear and tear over time.

By comparison, induction lights do not use electrodes to initiate a current during startup. Instead, the units leverage a generator (high frequency) and a power coupler. A radio frequency magnetic field is generated, which is used to activate the internal components of the fixture.

Comparing Light Output

Like LEDs, induction lamps can be toggled instantly without flickering. Moreover, the units provide accurate CRI ratings, at a range of 80+. This allows the fixtures to be used for detailed tasks and paint spray booths (Class I, Division 1 or 2 required).

Comparing energy efficiency rates, induction lights offer roughly 90 lumens-per-watt during illumination. LEDs perform slightly higher than this at a rate of 120 lumens-per-watt, when in use.

To conclude, LEDs clearly outperform induction lamps – but not by a wide margin. However, the nascent state of LED technology suggests there is plenty of room for improvements and upgrades. The gap between the performance of LEDs and incandescent lights or metal halide fixtures is considerably larger.

Share Button

Continue Reading

work lighting systems
Led Lights

What are Light Reflectors in Work Lighting Systems

Buildings and office spaces incorporate different designs, based on the illuminative requirements of the business. Because of this, work lighting systems should be customized to effectively cater to the unique layout of the space.

An effective way to ensure all sections of the work site are adequately illuminated is to utilize light reflectors. The components, which come in various sizes and shapes, are usually included in the design of the luminary. Understanding how reflectors work inside directional light sources, such as LEDs, and omni-directional luminaries, including incandescent bulbs and metal halide lamps, can help operators optimize lighting configurations in the area.

LEDs and Light Reflectors in Work Lighting Systems

LEDs may incorporate one or more secondary optics to extend or position light beams directly at the target. Reflectors inside LED lamps surround the diode or chip (depending on the type of LEDs). The material must be shiny and uniform in order to ensure smooth lighting effects. As a directional light source, reflectors are not crucial components for LEDs, since most of the light beams exit the lamp without requiring help from reflective surfaces.

It is important to consider that incorrect usage of light reflectors can lead to unwanted glare. When it comes to materials, LED reflectors are typically constructed of plastic or metal.

Tips and Recommendations

Light reflectors are cost-effective solutions for maximizing light output. As mentioned earlier, omni-directional light sources can benefit from reflectors, because they emit light in all angles. However, they are not suitable for compact installations in tight spaces, as reflectors tend to take up a lot of space in the luminary.

To prevent damaging reflectors, it is recommended for the housing and lens to be constructed of sturdy materials. Moreover, water-tight enclosures could help reduce the buildup of tiny droplets inside the unit, which could negatively affect light distribution during illumination.

Share Button

Continue Reading

Uncategorized

Take A Trip South for Columbus Day

Now that everybody has packed up and taken off to get back to school or work it is time for you guys who’ve spent the summer looking after the home and seeing that the college students and high-schoolers are well occupied to get a little time to yourselves.  When autumn rolls around it’s just the time to take a long weekend and enjoy the sights and activities you can find when you visit Riviera Maya.  Let yourself enjoy the night life under the lights in their resort clubs and entertainment centers.

 

Now don’t panic at this suggestion.  Many folks tend to feel that it isn’t right to go off and relax while the kids are busy studying and working.  But in truth, that is often the best time to do so.  It shows you have faith in their ability to look after themselves and the household while you are away.  And it also shows that you trust them to do their duties and their schoolwork without you peeking over their shoulder.  Furthermore, while you may be off on your own private vacation, you are still just a text mail or smartphone call away.  So while you can relax and enjoy the daytime sights and nighttime sounds you can get when visiting Experiencias Xcaret.  There you can enjoy numerous clubs and shows; visit some of the historic sights and cultural marvels, enjoy one of the many theme parks or just relax and cool out in the climate and atmosphere you’ve always heard about.  Your youngsters may even want you to go scout for them, since they will undoubtedly have the place on their list as a potential place to go to during their next spring break.

 

But your real break will be the savings you can get by using a Groupon coupon to pay for your entry fees when you go there.  You can save a significant amount up to 20% discount when you use a Groupon promo code.   And you can get up to 15% off 20 or more activities and meals at Xel-Ha with a Groupon promo code.  You can make all the arrangements online when you visit their website.  So take your lady now and fly off to the lovely shores to relax and savor the atmosphere together.  Visit the land where Columbus landed in time for Columbus Day!

Share Button

Continue Reading

led lights
Led Lights

What colour temperature LED should you buy?

Led spotlights come in two colour temperatures as standard; warm white and cool white. Understanding the difference between these two types of light and their suitability for certain applications is an important part of the buying process and will ensure complete satisfaction.

What is a colour temperature?

Unsurprisingly, when it comes to artificial illumination, there are many different “types” of light. Many people recall that when Compact Fluorescent Lamps (CFLs) were first introduced to homes there were many complaints that the light seemed much “colder” than traditional halogens. This is because they had a different colour temperature.

Colour temperature is one of the main characteristics of visible light and determines how warm or cold the light is. All colour temperatures are assigned a number called a Kelvin Rating. Colours with lower kelvin ratings are generally warmer while those with higher kelvin ratings are cooler.

Warm led spotlights colours are very soft with a slightly yellowy tint and are a close, but not perfect, replication of traditional halogen bulbs. Cool colours are very bright with a faint blue tint and are sometimes compared to the light given off by fluorescents.

Which works well where?

While colour temperature is a largely subjective matter and many customers have personal preferences to satisfy, there are a few “rules of thumb” which can help you to decide.

Due to its softness, Warm White is generally better for creating ambient/general light schemes. It is also good at promoting a relaxing and comfortable environment, so should also be used in “habitat” or “living” spaces. These may include the living room, bedroom, hallways or dining room. See more

Colour temperature – or simply what colour led spotlights will the bulb put out.

  • Pretty straightforward answers here:
  • Warm White is an ideal match to traditional Halogen bulbs/incandescent bulbs and produces amore warmyellow light with a colour temperature 3200K (probably the one most people are used too)
  • Pure White produces a white light which is often used in commercial environments or to create a very modern look with a colour temperature of 6500K.
  • You may find when looking at your products online that they quote a figure as above showing a high number with a K at the end, this is just the colour temperature output in the unit Kelvins (K). Some websites will show you a pretty chart with the colour temperature range from warm white to cool white along with the Kelvin scale, quite useful as it shows you what the output is likely to be (see above).
  • Cool White is more commonly used in public spaces, such as offices and shoppingcentres. It has a tendency to be too bright for general illumination, resulting in a room aesthetic that is too clinical for some. However, it is not uncommon to find this type of light used in kitchens and bathrooms as it works well with reflective and pearl surfaces. Feature and task lighting also benefit more from the brighter cool white, particularly as it helps to promote alertness. If you have a home office you might consider using it in there to help you concentrate.

Using the two colour temperatures in combination with one another can sometimes create quite spectacular results. You will find this, particularly with “layered” or “dual purpose” light schemes. For instance, in an art gallery, warm white would be used to create soft background ambience while cool white led spotlights could be used to highlight artwork.

See more this site: http://www.kandeferplumbing.com/using-leds-preserve-artwork-illuminate-museums/

 

Share Button

Continue Reading

leds
Led Lights

Using LEDs to Preserve Artwork And Illuminate Museums

Powerful LEDs are revolutionizing the way museums operate and maintain expensive artifacts. The luminary’s compact size and non-invasive properties allow curators to illuminate artwork in the building without affecting sensitive elements. By comparison, some traditional light sources emit harmful UV rays, which could cause discoloration on paintings, when exposed for long periods of time.

Keep reading to understand how museums leverage LEDs for illumination, inspections and preservation.

Narrow Spotlight Configurations

When illuminating a small artifact on display, curators typically use very narrow spotlights, suspended in the air or mounted very high on the ceiling. The narrow beam stays tight and focused, as it lights up the piece. Narrow lighting configurations are preferred, because of their ability to keep beams within a specific range, without affect nearby paintings. Furthermore, it keeps the general area dim, maintaining a comfortable ambiance for conversations and discussions.

Utilizing a wide flood beam to illuminate multiple pieces on a wall is not recommended, as it could cause unsightly glare – especially if the light source is very close to the wall (and if the color of the wall is bright). Flood beams would be an exception for very large museums, focusing on very large pieces (such as a dinosaur statue) or for dark-colored walls.

Detecting Inconsistencies (Infrared Light)

Behind the scenes, museums curators rely on infrared LED to streamline the detection of inconsistencies, origin of artifact and fraudulent applications. For instance, infrared light could be applied to uncover hidden touch ups in old paintings. In other industries, like law enforcement, infrared LEDs are also being used to detect counterfeit banknotes.

To conclude, the advantages of LEDs have made museums more efficient, authentic and grand. Without needing to invest in costly UV filters and outdated fixtures, such establishments could improve the overall mood and experience of viewers in the area.

Share Button

Continue Reading

led lights
Led Lights

Tips for Lighting Art

When you are going to purchase LED spotlights for highlighting art, then you need to make sure that you remember all these tips. This is the only way that you can install the lights for enhancing the art correctly. There are many people who have tried to light art correctly, but they are struggling because of the fact that they don’t know a few simple tips. Here are a few essential ideas that you should look at in order to get the most out of your beatiful art:

Why people are choosing lighting for their art

There are many reasons why people are choosing lighting art, like installing LED spotlights for enhancing the art. The most common reason is that if you are going to have the right type of light, you are going to be able to put the focus on the art and not on another place that can take the focus away from the subject matter.

It doesn’t matter what type of art it is, having the right type of light is essential to make sure that people see the art when they walk into the room. The last thing that you want is that people don’t see the art and can’t really enjoy the art, because it is hung in a dark corner.

Choosing the right type of light

You need to make sure that you are going to choose the right type of light for the type of art that is hanging. This is the only way that you can make sure that you are going to get the effect that you are looking for.

There are different types of lights, but most professionals recommend that you should install the LED spotlights to make sure that you get the right art lighting effect. Other lights might not be the best option for your art.

led lights

Why the LED lights are a better option

You might wonder why the LED lights are the better options when you are going to install lights to your art. There are many reasons why the LED spotlights are the much better option is because they are more durable and you don’t need to replace it as often as any of the other type of lights. checkout latest news at https://thewest.com.au/news/south-western-times/exhibition-spotlights-indigenous-stories-through-art-ng-b88508965z
LED lights are also a lot more economical and will ensure that you are going to save money on your utility bill at the end of the month, especially if you are going to have the lights to the art on throughout the day. LED lights don’t use as much energy as other lights that you can also use for lighting art.

These tips are going to make it easier to get the best lighting art effect. There are many people who try to get the same effect, but because they don’t know these tips, they don’t achieve the effect they hoped for. There are many different lights that you can choose for your art, but only one that is more recommended. LED spotlights are lights that you should use for lighting art and you should remember these tips for the best results with art lighting.

Share Button

Continue Reading